Check All | Uncheck All

Sand Control Systems

Series 5100 Inflatable Circulating or Squeeze Gravel Pack System
TTS Thru-Tubing Wash Down Gravel Pack
Series 5000 Thru-Tubing Frac Pack System
Vent Screen with Cement Cap
TTS Thru-Tubing Gravel Pack Screen Hang-Off
Series 5012 One Trip Retrievable Squeeze Pack System
Vent Screen with Isolation Packer and Overshot
TTS Thru-Tubing Perforating Gun and Screen Deployment

Service Tools

LSA–Locking Stinger Assembly
Snap Latch Stinger Assembly
Mechanical Setting Tool (MST) Assembly
Tension Packer Assembly

Product Information Packers-Well Information

Series 5011 Retrievable Packer Accessories
Series 5100 Inflatable Packer
Series 4800 Control Set High Expansion Packer
Series 5011 Retrievable Cement Retainer (Sliding Sleeve)
Series 5011 Retrievable Straddle Pack System
Series 5014 Retrievable Bridge Plug (RBP)
Series 5011 Retrievable Dual Seal Bore Tubing Packer
Series 5011 Retrievable Packer Setting Assemblies
Series 4800-Controlled Set High Expansion Cement Retainer

X-Span Tubing and Casing Patches

Tubing Patch Specifications
Casing Patch Specifications
X-Span Overview
X-Span Advantages and Applications

Workover-Completion Systems

Series 5200 Controlled Volume Displacement System (CVDS)
TTS Tubing Patch Straddle Pack Installation
TTS Thru-Tubing Gas Lift Velocity String Installation

Wireline Products

Series 4025–HPHT Wireline Pressure Setting Tool
Series 7850-ACE Thru Tubing Umbrella Plug
Series 8300-Gravity Bailer
Series 1800-Gage Hanger Retrievable
Series 8299-Flex Joint
Series 4010-Wireline Pressure Setting Tool (Power Charge)
Series 1200-Auto Release Tool
Series 7910 Electro-Hydraulic Bailer Bottom (EHBB)
Series 4250-Cast Iron Bridge Plug
Series 4100–Knock Out Magna-Range Bridge Plug
ACE Mix Cement Kits
Series 1000-Positive Displacement Bailer
Series 2105-TTS Tubing Bridge Plug (10K)
ACE Mix Cement (6 gallon) Kit Mixing Procedure
TTS Rental Equipment
Series 9306-Spiral Thru Tubing Bridge Plug
Series 4200-Fixed Slip Magna-Range Plug (Pressure Rated)
Series 1201-Selective Release Tool
Tech Unit-ACE Umbrella Plug
Series 4260-Cast Iron Cement Retainer
Series 4020-Hydrostatic Setting Tool (Non-Explosive)

Check All | Uncheck All


Series 1200 – Auto Release Tool

The Thru Tubing Systems Auto Release Tool is designed for use with wireline deployed explosive or propellant tools. It is installed as an integral component in the tool string between the CCL and the firing sub attached to the top of the tool body. The purpose of the tool is to guarantee separation of the expended or used downhole tool from the basic wireline BHA (cablehead, sinker bars, CCL) used to deploy the downhole tool.

An operator may wish to jettison a downhole tool for a variety of reasons although it is primarily due to a possible change in tool OD or shape that would make retrieval to the surface risky. This would be the case with perforating guns, jet cutters, etc. The Auto Release Tool separates at the time of downhole tool function. It utilizes pressure from the tool activation and/or subsequent BHP flooding into the tool after activation. The tool operation is passive from the operator’s point of view, no subsequent firing of secondary detonators or additional surface operations must be performed for the expended tool to be released.

Special features incorporated into the design of the Auto Release Tool eliminate possible problems that have been encountered when utilizing other commercially available release tools. Some available tools require the lower half of the tool string to be stuck and the top side to be pulled using the wireline unit to cause the components to separate. One unique feature of the Auto Release Tool is the positive separation of the Wireline BHA from the expended tool. This is accomplished by an internal shifting piston applying opposing force between the two halves and causes separation without assistance from the wireline unit. The Auto Release Tool was actually designed to function when deployed in a horizontal section of a well.

Another feature of the Auto Release Tool’s design is the distribution of weight and applied forces on the tool components. The weight of the downhole tool string is distributed to a series of steel balls or of keys located in an internal profile. This eliminates the possibility of an accidental release during primary tool actuation, by the forces exerted on the severing tension bolt used to suspend the downhole tool on other commercially available tool releases.

The Auto Release Tool is capable of carrying a total tool load of up to 10,000# and will operate at BHP of 15,000 psi. The BHT is only limited by the explosives and seals selected. The upper portion of the Auto Release Tool returned to the surface is easily re-dressed for re-use.

Specifications

 

Series 1200 Auto Release Tool

 Model Number

1200-169-A-004

1200-169-A-006 (Top Fire)

 OD

1.69”

1.69”

MAX BHP

15,000 psi

15,000 psi

MAX TOOL STRING WEIGHT

10,000#

10,000#

LENGTH (Overall)

15.57”

18.50”

LENGTH (Run-in)

14.19”

15.86”

LENGTH (Left in hole)

4.71”

6.39”

CONNECTION (Top)

1-3/16”-12

1-3/16”-12

CONNECTION (Bottom)

1-3/16”-12

‘GO’ Button (long)